Showing results: 631 - 645 of 1099 items found.
-
Bestone Industrial Ltd.
Used in rubber plastic, textiles, waterproof materials, wire and cable, metal materials tensile, compression, bending, cutting and mechanical propertie test, increase the affix to do bending test, it is scientific research institues, universities and colleges,industrial and mining enterprises, the technical supervision and inspeciton arbitration of the department idea test equipment.
-
KT-468 -
KILTER ELECTRONIC CO.,LTD
Test device used UTP and STP network wiring and phone line. Check continuity and configuration of wiring with unshielded and shielded modular plugs. Test for open circuits,shorts,miswires and reversals. SHIELD detection tests a cable`s shield integrity. Main unit and one remote allow one person testing
-
A910 -
AGM Elettronica
The A910 is a short circuit locator designed for fault location in power cables. The instrument measures the ratio of the resistances of the two sections of failed conductor using a four-wire "Kelvin" connection, thus eliminating errors associated with contact resistances of the test leads. With the A910 you can determine if the cable has more than a short and locate the first and the last fault. The instrument locates fault with an insulation resistance up to 5 Mohms in cables that have a total resistance greater than 5mohm (approximately 90 m of 300 sqmm cable) and less than 30 kohms. The distance to fault is measured as a percentage of the total length of cable and is displayed on a large LCD display.
-
DMX ADAPTER -
EMO Systems Canford Audio PLC
DMX protocol is a standard means of controlling lighting dimmers remotely from a control desk. The standard uses a three wire connection using 5-pin XLR type connectors. These adapters allow the E445, E446 and E447 table testers to be used to test the primary circuit of such cables. Two adapters are required for each cable tester.
-
Optical Wavelength Laboratories
Deluxe color LCD fiber link certifier (includes MASTER and REMOTE devices) Tests two fibers at a time, cutting testing time in half (when compared to traditional fiber certification) Ideal for installers and contractors who need to certify fiber cables BI-DIRECTIONALLY Measure the end-to-end length of the fiber cable with every test Unlimited sets of job parametersOWLView software allows tri-report capability certification, OTDR, and endface all on one report) Multimode and singlemode options available.
-
TM263N -
T&M Tools Limited Co
◇ Added Network Cable Test ◇ Accurately test whether a single network cable transmits signals normally ◇ Self Calibration ◇ Set the Auto Off ◇ Wavelength Memory function after turn off the tester ◇ High Accuracy, high ,High sensitivity, high linearity ◇ Stable VFL Output ◇ USB Charge port ◇ FC,SC Connector ◇ 18650Li-ion Battery ◇ Lower power consumption design, long standby time ◇ Rubber Out shell, increased the protective properties for field work
-
CKT1175-20 -
CK Technologies, Inc.
The CKT1175-20 is a high-voltage wiring analysis system that features rack-mounted switching matrices. This system is expandable in 100 test point increments to 96,000 test points, and available with a wide variety of adapter cable interface connectors, with the standard interface being the CKT MAC interface system.
-
KT-45 -
KILTER ELECTRONIC CO.,LTD
Quickly test twisted cable RJ45 and BNC connector including T568A/B, 10-Base-T (UTP/STP), Token Ring, etc. Automatic test for open circuits, shorts, reversals, miswires, continuity. Main unit and one remote allow one person to test. Includes protective leather pouch. Testing before and after installation
-
TM800H -
T&M Tools Limited Co
TM800H Handheld Cable Fault Locator adopts TDR (Time Domain Reflection), new signal process and data collection technology. It can locate the distance of cable break and mix faults accurately. TM800H can be widely used in the communication installation, maintenance and general wiring. It can troubleshoot not only the local Telco-cable, but also Network cable. Its high sampling rate makes the measurement dead zone as narrow as 1 meter. This makes it a straightforward, user-friendly test solution.
-
YAV90Q04 -
6TL Engineering
The interface YAV90Q04 permits to connect two YAV90096 boards to one 192-Signal contacts Quadrapaddle module. As the Mini-D 50 connectors let 2 free pins (1 and 26), these pins are interconnected to a test point, with the possibility of be grounded. Cable P/N J6200540: Mini-D-50 to Mini-D-50 IDC connectors with 400 mm flat cable.
-
PR-09SCSIV -
Pansco, Ltd
The Universal Cable Tester is a compact, stand-alone unit which gives technicians an affordable way to test PC, serial ATA, network, telecom, coaxial, USB A/B, mini USB A/B/AB, 1394 Firewire 4/6, and SCSI I, II, III, and V cables for continuity, wiring configuration, opens, shorts, miswiring, and cross-connected wires.
-
VFF5 -
IDEAL NETWORKS
Used to verify continuity, test and find breaks in fibre links, locate pinched fibre strands in termination cabinets, or anywhere fibre optic cables are terminated and subject to mechanical damage.
-
NG 600 -
Unaohm Start S.r.l.
The NG 500 noise generator is an external module with dual power supply for different applications: to calibrate filters, switchboards, to the distance of a fault caused by the impedance mismatch, to test the cable efficiency.
-
Luna Innovations Inc.
Test and characterize fiber optic cables, assemblies and network with unmatched speed, precision and spatial resolution. Luna’s OBR reflectometers can analyze loss with a spatial resolution and sensitivity unmatched in the industry.
-
Extech UM200-KTL -
Extech Instruments Corporation
The Extech UM200-KTL is a set of 4 wire cables with Kelvin clip connector test leads for the Extech UM200 battery powered milliohm meter. Use them as extras or as a spare if necessary.